Repainting your house not only gives it a new look but it also lengthens its life. If you were not aware of this, its time you prepared yourself to start such a project. Interior painting Dallas, TX is meant for all surfaces in the house ranging from walls and ceiling to the floor.
Good preparation is what determines the end product of painting work. Thus, ensure you get it right. Start by clearing furniture from the room. If they are too heavy to be moved, you can just have them covered. Plastic material make good covers but there is a new material in the market made of canvas which not only absorbs stray paint but does not slip easily.
Light-electrical switches, pictures, mirrors and window treatments should not be on the walls by the time the project kicks-off. Having dirt on the surface to be repainted decreases the probability of adhesion. Thus, they should be washed. However avoid using harsh detergents which would do more harm than good. Attention should be given to places with oily residues, soiling or touched frequently in city Dallas, TX.
Drying should be done after they have become clean. In case the wall has markings from pens, crayon or water stains, they should be scrubbed too. For glossy areas, sanding is the most effective preparation method. It leaves behind dust thus you need to clean it afterwards. Loose paint ought to be removed too. Make use of putty knife to make the work easier.
If there are surface imperfections, cracks or nail holes on the ceiling surface, wall or floor, rake out large plaster or other particles in them. Sparkling compound should then be pressed firmly inside such imperfection until the compound gets at the same level with the floor surface. If there are crevices on the door-wall junction, then this compound can be used to fill them up. After it has dried, ensure sanding is done.
The roller gets soaked with painting as the project proceeds. You can do way with the excess one on paint tray. The room corners must be painted first in a width-wise motion as opposed to length-wise. This ensures that you do not end up straining your neck and back while moving the brush along the wall.
After the ceiling has been fully painted, you can then go back to the starting site. The line between the wall and ceiling needs to be done with a small brush. Extend out about three inches from the door or window edge. The field can be then be filled with a roller. To ensure the process proceeds systematically, divide it into small sections.
Blue tape should be used on wall-trim intersection after the paint dries. Paint baseboards, moldings, floor frames and window frames using an angled brush at 2-inches. The top of windows or doors should be given priority over the baseboards. Color blending is vital and you can outsource help in achieving this if you are not knowledgeable concerning such matters in Dallas city, TX.
Good preparation is what determines the end product of painting work. Thus, ensure you get it right. Start by clearing furniture from the room. If they are too heavy to be moved, you can just have them covered. Plastic material make good covers but there is a new material in the market made of canvas which not only absorbs stray paint but does not slip easily.
Light-electrical switches, pictures, mirrors and window treatments should not be on the walls by the time the project kicks-off. Having dirt on the surface to be repainted decreases the probability of adhesion. Thus, they should be washed. However avoid using harsh detergents which would do more harm than good. Attention should be given to places with oily residues, soiling or touched frequently in city Dallas, TX.
Drying should be done after they have become clean. In case the wall has markings from pens, crayon or water stains, they should be scrubbed too. For glossy areas, sanding is the most effective preparation method. It leaves behind dust thus you need to clean it afterwards. Loose paint ought to be removed too. Make use of putty knife to make the work easier.
If there are surface imperfections, cracks or nail holes on the ceiling surface, wall or floor, rake out large plaster or other particles in them. Sparkling compound should then be pressed firmly inside such imperfection until the compound gets at the same level with the floor surface. If there are crevices on the door-wall junction, then this compound can be used to fill them up. After it has dried, ensure sanding is done.
The roller gets soaked with painting as the project proceeds. You can do way with the excess one on paint tray. The room corners must be painted first in a width-wise motion as opposed to length-wise. This ensures that you do not end up straining your neck and back while moving the brush along the wall.
After the ceiling has been fully painted, you can then go back to the starting site. The line between the wall and ceiling needs to be done with a small brush. Extend out about three inches from the door or window edge. The field can be then be filled with a roller. To ensure the process proceeds systematically, divide it into small sections.
Blue tape should be used on wall-trim intersection after the paint dries. Paint baseboards, moldings, floor frames and window frames using an angled brush at 2-inches. The top of windows or doors should be given priority over the baseboards. Color blending is vital and you can outsource help in achieving this if you are not knowledgeable concerning such matters in Dallas city, TX.
No comments:
Post a Comment